top of page

How to Install the Yofer Dark Night Body Kit on the 11th-Gen Honda Civic

Oct 20
4 min read

The Yofer Dark Night kit for the 11th-gen Civic sedan mounts with a combination of automotive double-sided tape, factory clips and screws, using existing mounting points wherever possible. This guide follows Yofer's official installation video and covers each part of the kit in the order it's installed:


  1. Four-piece front lip

  2. Side skirts

  3. Rear corner spats

  4. Rear diffuser with integrated brake light

  5. Trunk spoiler


What you'll need

  • Adhesion promoter and clean wipes

  • Automotive double-sided tape (if not pre-applied)

  • Cordless drill/driver or screwdriver

  • Trim clip tool for factory clips

  • Basic tools to remove the taillight (for the diffuser light wiring)


Tip: Every taped part follows the same routine: clean, adhesion promoter, tape, test-fit, peel, press. Take time on the test fit. Once the tape backing is off, repositioning is difficult.



Part 1: Front lip (four-piece)

The four-piece front lip on the 11th-gen Civic

The front lip is a four-piece split design: two side sections plus an upper and lower center section.


Step 1: Prep the side sections

Wipe adhesion promoter onto the taped areas of the part, then apply the double-sided tape.


Applying adhesion promoter to the front lip tape area

Step 2: Align, peel and press

Hold the piece in position and check the fit. Once it's aligned, peel the tape backing and press the part firmly into place.


Aligning the front lip side section on the bumper

Step 3: Clip and screw

Reinstall the factory clips along the bottom edge, then fit the screw on the side. Repeat steps 1–3 on the other side.


Reinstalling factory clips under the front lip

Step 4: Upper center section

Before fitting the upper center section, remove the two factory clips at the bottom center of the bumper. Align the screw posts at both ends, reinstall the factory clips, then drive screws into the posts at each end.


Fitting screws to the upper center section

Add four more screws along the underside for reinforcement.


Adding reinforcement screws under the front lip

Step 5: Lower center section

Align the lower center section and fit screws into its four screw posts.



Part 2: Side skirts

Step 1: Prep

As with the front lip, wipe adhesion promoter on the taped areas and apply the double-sided tape.


Applying adhesion promoter to the side skirt

Step 2: Peel the middle section first

Peel the backing from the middle section of tape only. This tacks the skirt in place while leaving the ends adjustable.


Peeling the middle section of side skirt tape

Step 3: Align, peel and press

Position the skirt, check the alignment, then peel the remaining tape backing and press firmly along the full length.


Aligning the side skirt under the door

Step 4: Screw in

Fit screws at the factory screw locations. There are also two screw locations on the underside.


Fitting the side skirt at the factory screw location


Part 3: Rear corner spats

The rear corner pieces go on before the diffuser.


Step 1: Prep both surfaces

Apply the double-sided tape to the spat, then wipe adhesion promoter onto the mounting area of the bumper.


Applying double-sided tape to the rear spat

Step 2: Align and press

Line the spat up, then press it firmly into place.


Pressing the rear spat onto the bumper

Step 3: Screw in

Reinstall the factory screw on the side and fit a screw underneath. Repeat on the other side.



Part 4: Rear diffuser with brake light

Step 1: Prep

Wipe adhesion promoter on the diffuser's taped areas and apply the double-sided tape. Peel the backing from the middle section first, then wipe adhesion promoter on the mounting area of the bumper.


Prepping the rear diffuser with adhesion promoter and tape

Step 2: Align, peel and press

Fit the diffuser into position, check the alignment, then peel the remaining tape and press firmly.


Aligning the rear diffuser

Step 3: Screw in

Fit screws underneath on both sides, then add two screws at the bottom center for reinforcement.


Fitting reinforcement screws under the rear diffuser

Step 4: Wire the brake light

To connect the diffuser light, remove the factory taillight. Route the light wire out directly below the taillight and connect it to the factory plug.


Removing the factory taillight for wiring access

Connecting the diffuser light to the factory plug

Secure the wiring harness, then reinstall the taillight.


How the diffuser light works

  • Parking lights on: the center light stays steadily lit.

  • Braking: it brightens to act as an additional brake light.


Rear diffuser light on with the parking lights

Rear diffuser light brightening under braking


Part 5: Trunk spoiler

Step 1: Test-fit and mark

Before applying anything, test-fit the spoiler on the trunk lid to find the exact mounting position.


Test-fitting the spoiler on the trunk lid

Step 2: Prep, peel and press

Apply the double-sided tape to the spoiler and wipe adhesion promoter on the mounting area. Set the spoiler in place, peel the tape backing, and press evenly along its whole length.


Pressing the spoiler evenly onto the trunk lid

That completes the installation.



FAQ

Does the Yofer Dark Night kit require drilling?

The kit mounts with double-sided tape, factory clip locations, factory screw locations and the kit's own screw posts. Check the instructions supplied with your kit for your specific vehicle before installation.


Which parts need wiring?

Only the rear diffuser, which has an integrated light. It connects to the factory plug behind the taillight.


What does the rear diffuser light do?

It stays lit with the parking lights and brightens when you brake.


In what order should the parts be installed?

Front lip, side skirts, rear corner spats, rear diffuser, then the trunk spoiler. The rear spats must go on before the diffuser.


Should I install it myself or use a shop?

The process uses basic hand tools, but taped parts can't easily be repositioned. If you're not comfortable with test-fitting and alignment, a professional body shop or installer is recommended.



Yofer kits for the 11th-gen Civic

The installation process is broadly the same across Yofer's 11th-gen Civic kits. See the kit for your car:


Installation steps and images from Yofer Design's official installation video.


Honda Civic 11th Gen Dark Night Pro installation video

Comments


bottom of page