Toyota Camry 9th Gen Body Kit Install Guide
This guide follows the Yofer video for the Toyota Camry 9th Gen 2024 Body Kit on the 9th-gen (XV80) Toyota Camry. The kit is a front bumper and rear diffuser (shown as a Luxury or Sport rear lip with a center light). The daytime running lights and exhaust tips in the video are extras, sold separately. Check the product page for what you're ordering.

Watch the full installation
The captions in this video are in Chinese (with Mandarin narration); the written steps below are in English.
What you'll need
Items named in the video:
Front bumper body, fog light surrounds, grille, front trim panel, tow-hook cover and radar bracket
Luxury-version or Sport-version rear lip, center light and plug-in wiring harness
Optional DRL set with metal clips and brackets
For the Sport rear lip: two exhaust pipe sections, four carbon-fiber tips, rubber hangers and clamps
Adhesion promoter, double-sided tape, a cordless driver and a trim tool
Part 1: Assemble the front bumper
Step 1: Fog light surrounds. Clip the surrounds onto the bumper body, then fasten them at the screw points.

Step 2: Front trim. Clip the front trim piece onto the bottom of the bumper and fasten it with screws. The lower middle is held by clips, with screws reinforcing both sides.

Step 3: Transfer factory parts. Refit the factory trim cover, then mount the rear trim-panel bracket and the ACC module at the screw posts on the back.
Step 4: Radar bracket. At the radar opening, wipe on adhesion promoter and stick on the bracket. Refit the radar and secure the wiring, then refit the tow-hook cover.

Part 2: Optional daytime running lights
Step 5: Mount the DRLs. Clip the metal clips onto the plastic tabs behind the bumper. Feed the DRL harness through the vent opening, then fasten the side and upper/lower brackets with screws.

Step 6: Connect them. Run the harness under the headlight into the engine bay and plug it into the factory headlight, then tidy the wiring.

Part 3: Fit the front bumper
Step 7: Mount it. Secure the bumper at the factory clip points and refit the wheel-arch clips. Fit the bracket underneath and refit the factory clips and screws. Then refit the engine-bay cover and mount the plate bracket.

In the video's demo, the DRLs show a white running light and work as left and right turn signals.

Part 4: Luxury rear lip
Step 8: Remove the factory lip. Remove the factory rear lip and the reflectors.
Step 9: Assemble. Clip the corner pieces onto the middle section and screw them from behind. Clip in the chrome trim.

Step 10: Mount the center light. Apply adhesion promoter and tape to the back of the center light, fasten its screws, and refit the red reflectors.
Step 11: Wire it. Remove the tail-light cover and screws and take the tail light out. Route the harness up from underneath, unplug the tail light, connect the adapter plug, and refit the tail light.
Step 12: Fit the lip. Fit it to the factory clip points. Install the factory metal clips, fasten the screws, and refit the clips underneath.

Part 5: Sport rear lip and exhaust tips
Read this first: the video cuts the factory exhaust pipe to fit the new tail section. The exhaust tips are an extra item on our listing, so this step only applies if your order includes them. Cutting the pipe is a permanent change to the car and may affect emissions compliance and your vehicle warranty. Check your local rules, and we recommend having a professional exhaust shop do this step.
Step 13: Prepare. Remove the factory rear lip. In the video, the factory exhaust pipe is cut, leaving about 40 mm.

Step 14: Hang the tail section. Attach the rubber hanger to the tow hook under the right side of the rear bumper. Join the two exhaust sections and place the clamp on the joint. Set the tail section inside the rear under-panel and hook it into the hanger.
Step 15: Connect and tighten. Line up the left joint with the factory pipe and tighten the clamp bolt.

Step 16: Tips and lip. Lock the carbon-fiber tips onto the outlets, then fit the Sport rear lip at the factory clip points.


Tip: tape and adhesion promoter
In this video, adhesion promoter and tape are used where parts bond rather than clip: the radar bracket and the back of the center light. Clean the surface, wipe on the promoter, and apply the tape before pressing the part in place. Follow the drying times in your product's instructions.
FAQ
Do I have to cut the exhaust?
Only if you add the exhaust tips. They're an extra item on our listing, and the video cuts the factory pipe only to fit them with the Sport rear lip. The front bumper, DRLs and Luxury rear lip need no exhaust work. Tell us which parts you're ordering if you're not sure.
Do I need to drill holes in my car?
No drilling is shown. The front bumper, DRLs and Luxury rear lip use clips, screws and the factory mounting points, and the radar bracket is stuck on with adhesion promoter and tape. The one permanent change in the video is cutting the factory exhaust pipe, and that's only for the optional exhaust tips that go with the Sport rear lip (see the warning in Part 5). Without them, the kit matches our listing's description of no cutting or additional bodywork. If a screw point doesn't line up on your car, contact us before you drill anything. Our Returns policy doesn't cover damage caused during installation.
Will the radar and driver-assist systems still work?
The video transfers the factory radar into the new bumper. After any work involving the radar, confirm your driver-assist systems work and have a dealer check calibration if needed.
Which years does it fit?
The Yofer catalog lists this kit for the 2025-and-later Toyota Camry (9th Gen, XV80). Confirm against the product page before ordering.
What if a part arrives damaged, defective or wrong?
Inspect your order when it arrives. Our Returns policy explains how to report damage or defects, the deadline for reporting, and what isn't covered (for example, damage caused during installation). Delivery times and details are on our Shipping policy page.
Installation steps follow the manufacturer's video and are for reference only. Fitment, hardware and required work can vary by vehicle. For what's covered if a part arrives damaged or defective, see our Returns policy; for delivery details, see our Shipping policy. If you're not comfortable doing the work, have a professional install the kit.





Comments