Honda Accord 11th Gen 2023 MAX Front Bumper Install Guide
The Honda Accord 11th Gen 2023 MAX Body Kit replaces the front end with a three-piece front bumper. This guide follows the Yofer video for that front bumper. It's a 13-step bench assembly followed by five steps to fit it to the car.

Watch the full installation
The captions in this video are in Chinese (with Mandarin narration); the written steps below are in English.
What you'll need
MAX three-piece front bumper, front lip and license plate frame
The supplied under-panel and hardware
Your factory air guides, radar bracket, grille brackets and connecting parts (they get transferred over)
A cordless driver, screwdrivers and a trim/clip tool

Part 1: Assemble the front bumper
Step 1: Fit the black trim. Clip the black trim pieces into their spots on the left and right of the bumper.

Step 2: Join the bumper to the lip. Clip the bumper onto the matching clip points on the lip, and make sure every clip is fully seated.

Step 3: Reinforce the middle. The lower middle is held by clips, with screws reinforcing both sides.
Step 4: Transfer the air guides. Refit the factory air guides on both sides with clips and screws.
Step 5: Transfer the radar bracket. Refit the factory radar bracket onto the lower section or the matching spot on the factory lower grille.

Step 6: Fasten the bumper brackets.
Step 7: Fit the grille. After fitting the grille, fasten the grille brackets and the grille mesh.

Steps 8-10: Harness, radar and connectors. Clip the wiring harness back into its retainers, mount the radar in its position, and refit the factory connecting parts.
Step 11: Fit the under-panel. Clip the dedicated under-panel to the bottom of the bumper.

Steps 12-13: Finish the assembly. That completes the bumper assembly. Finally, fit the license plate frame.

Part 2: Fit the bumper to the car
Reconnect the front bumper harness connectors.
Fasten the clip points on the left and right.
Refit the factory screws at the wheel-well liner.
Secure the under-panel with clips and screws.
Fasten the factory connecting parts.

Tip: tape and adhesion promoter
The front bumper in this video goes together with clips and screws only. It doesn't show double-sided tape or adhesion promoter. If your kit also has taped pieces, such as the side skirts, use the routine from our other Yofer guides: clean, wipe on adhesion promoter, apply tape, test-fit, then peel and press. Follow the drying times in your product's instructions.
FAQ
Does the radar have to move?
Yes. The video moves the factory radar bracket and radar into the new bumper. After any bumper work that involves the radar, check that your driver-assist systems work, and have a dealer check calibration if you're unsure.
Do I need to drill holes in my car?
No. The MAX bumper is assembled on the bench with clips and screws. It then goes onto the car at the factory clip points, the factory screws in the wheel-well liner and the factory connecting parts. The factory radar bracket and air guides are moved over to the new bumper, not modified. That matches our product listing, which describes the kit as needing no cutting or additional bodywork. If a screw point doesn't line up on your car, contact us before you drill anything. Our Returns policy doesn't cover damage caused during installation.
What else is in the MAX kit?
Our listing includes the front grille, front bumper, rear diffuser and side skirts. This video covers the front bumper only.
What if a part arrives damaged, defective or wrong?
Inspect your order when it arrives. Our Returns policy explains how to report damage or defects, the deadline for reporting, and what isn't covered (for example, damage caused during installation). Delivery times and details are on our Shipping policy page.
Installation steps follow the manufacturer's video and are for reference only. Fitment, hardware and required work can vary by vehicle. For what's covered if a part arrives damaged or defective, see our Returns policy; for delivery details, see our Shipping policy. If you're not comfortable doing the work, have a professional install the kit.





Comments