top of page

Honda Accord 10th Gen Restyling Rear Lip and Center Light Install Guide

4 days ago
3 min read

Updated: 5 hours ago

This guide covers the rear lip (listed as the rear diffuser) from the Honda Accord 10th Gen Restyling 2021 Body Kit. It follows the Yofer video. The lip clips and screws to the factory points, and its red center light is wired into the driver-side tail-light connector.

Honda Accord at night with the Yofer rear lip and center light lit

Watch the full installation

The captions in this video are in Chinese; the written steps below are in English.

What you'll need

  • Yofer rear lip, under-panel, center light and the supplied adapter plug

  • The supplied screws (the video shows small silver screws and large black screws) and self-tapping screws

  • A cordless driver or screwdriver

  • A trim/clip removal tool

  • Access underneath the car, such as a lift or safely supported ramps

Part 1: Assemble the rear lip

Step 1: Fit the under-panel. Slot the under-panel into its matching position on the rear lip.

Slotting the under-panel into the Yofer rear lip for the 2021 Honda Accord

Step 2: Lock it in. The video locks the under-panel in place with self-tapping screws.

Part 2: Mount the rear lip

Step 3: Line it up. Offer the rear lip up to the car and line it up. Once it's aligned, snap the clips in one by one.

Two installers lining up the rear lip on the back of a white Honda Accord

Step 4: Seat the corners. Line up the corners next to the exhaust tips and secure them with clips at the factory mounting points.

Aligning the rear lip corner next to the Accord's exhaust tip

Step 5: Tighten the under-panel screws. The first position takes a small silver screw. The second and third positions take large black screws.

Part 3: Wire the center light

Step 6: Mount the light and route the wire. Fit the center light and run its wire along the underside of the rear bumper.

Mounting the red center light and routing its wire on the Accord rear lip

Step 7: Reach the tail light. Remove the trunk trim panel and feed the wire through the hole. Then remove the driver-side tail light and unplug its connector.

Removing the driver-side tail light to reach the wiring connector

Step 8: Connect the adapter. Plug the supplied connector into the tail light.

Plugging the supplied adapter connector into the Accord tail light

Step 9: Seal the pass-through. Pass the wire out through the wiring hole. Use the factory rubber grommet to seal it and hide the wire.

Part 4: Final fastening

Step 10: Clip the underside. Secure the bottom of the lip with the factory clips, one by one.

Securing the bottom of the rear lip with factory clips from under the car

Tip: wiring and fasteners

The lip in this video is held only by clips and screws, with no tape. The center light connects through a plug-in adapter at the tail light. If you aren't comfortable with lighting connections, have a professional do that step. After installing, check that your tail lights, brake lights and the center light all work.

FAQ

Do I need to drill holes in my car?

No. Nothing is drilled into the car. The only self-tapping screws in the video join the under-panel to the rear lip itself, on the bench. On the car, the lip goes onto the factory clip points and the under-panel screws go into existing holes. The light wire passes through an existing hole in the trunk, sealed with the factory rubber grommet. That matches our product listing, which describes the kit as needing no cutting or additional bodywork. If a screw point doesn't line up on your car, contact us before you drill anything. Our Returns policy doesn't cover damage caused during installation.

How does the center light get power?

In the video it's plugged into the driver-side tail-light connector through the supplied adapter. Lighting laws vary by state, so check your local rules for rear lighting.

Which Accord does this fit?

The Yofer catalog lists this kit for the 2021-2022 Honda Accord (the 10th-gen refresh). The Hybrid version covers the same years. Confirm against the product page. A separate Hybrid version of the kit is also listed.

What if a part arrives damaged, defective or wrong?

Inspect your order when it arrives. Our Returns policy explains how to report damage or defects, the deadline for reporting, and what isn't covered (for example, damage caused during installation). Delivery times and details are on our Shipping policy page.

Installation steps follow the manufacturer's video and are for reference only. Fitment, hardware and required work can vary by vehicle. For what's covered if a part arrives damaged or defective, see our Returns policy; for delivery details, see our Shipping policy. If you're not comfortable doing the work, have a professional install the kit.

Comments


bottom of page