top of page

Tesla Model Y 2025 Body Kit Install Guide

Oct 29
4 min read

This guide follows the Yofer video for the Tesla Model Y 2025 Body Kit on the refreshed Model Y (Juniper). In the video, every piece attaches with double-sided tape plus screws and clips at the wheel-arch liners and underneath.

Gray 2025 Tesla Model Y with the Yofer front lip installed, front view

Watch the full installation

The captions in this video are in Chinese (with Mandarin narration); the written steps below are in English.

What you'll need

  • Front lip main body with left/right corner pieces, side skirts, and rear diffuser main body with left/right corner pieces

  • The installation hardware pack, including screw bases and screws

  • Adhesion promoter and double-sided tape

  • A cordless driver and screwdrivers

The video's kit also includes a rear wing. Our listing includes the front lip, side skirts and rear diffuser, so check the product page for your kit's contents.

Yofer front lip main body for the 2025 Tesla Model Y laid out with hardware

Part 1: Assemble the front and rear pieces

Step 1: Join the corner pieces. Join the front and rear main bodies to their left and right corner pieces.

Joining the corner pieces to the Model Y front lip main body

Step 2: Fit the screw bases. Clip the screw bases into the screw holes on the underside of each main body. Seat the corner pieces from behind onto the screw posts, then tighten all the screws.

Part 2: Tape prep

Step 3: Adhesion promoter. Wipe adhesion promoter onto every bonding surface of the front, rear and side skirts.

Wiping adhesion promoter onto the kit's bonding surfaces

Step 4: Tape the edges. Apply double-sided tape along the edges of the bonding surfaces.

Applying double-sided tape along the edge of a side skirt

Part 3: Assemble the wing

Step 5: Build the wing. Join the wing ends to the main section and fasten them underneath with the supplied screws. Fit the trim cover. Then wipe adhesion promoter on the underside and apply tape.

Part 4: Install the front lip

Step 6: Prep and position. Clean the front bonding area on the car and wipe on adhesion promoter. Pull out the tape liner tabs and fit the lip over the factory front bumper, locating both sides first.

Two installers fitting the front lip onto a 2025 Tesla Model Y

Step 7: Peel and press. Peel the liner from one side and press the lip down as you work toward the other side.

Peeling the tape backing while pressing the front lip into place

Step 8: Fasten. Fasten the screws and clips at the wheel-arch liner, then the screws underneath.

Fastening screws at the wheel-arch liner with a cordless driver

Part 5: Install the side skirts

Step 9: Fit the skirts. Clean the bonding area. Lift the liner on the middle section of the skirt and pull out a tab. Position the skirt against the body, peel the liner and press down. Then fasten the front, rear and underside screw points.

Positioning the side skirt against the Model Y body

Part 6: Install the rear diffuser

Step 10: Fit the rear piece. Remove the clips on both sides of the liner and clean the rear bonding area. Lift the liner and pull out a tab, then fit the rear piece onto the factory rear bumper. Locate both sides, then peel the liner from one side and press toward the other.

Checking the rear diffuser's position on the Model Y rear bumper

Step 11: Fasten. Fasten the screws and clips at the wheel-arch liner, then tighten the screws underneath.

Part 7: Install the rear wing

Step 12: Fit the wing. Clean the bonding area, lift the liner and pull out a tab. Line the wing up, then peel the liner and press it down.

Peeling the tape backing and pressing the rear wing down

Tip: the tape and adhesion-promoter routine

For every taped part, the video wipes adhesion promoter on both the part and the car, and runs tape along the part's edges. It leaves a liner tab sticking out so the part can be positioned before the tape grabs. On the long pieces, it peels from one side to the other while pressing. Check your promoter and tape instructions for drying time and temperature limits, because the video doesn't state them.

FAQ

Does it fit the Model Y Performance?

No. The Yofer catalog lists this kit for the 2025-and-later Model Y, and our listing says it fits the Base and Premium versions but not the Performance version.

Do I need to drill holes in my car?

No drilling is shown or mentioned. Each piece is held by double-sided tape plus screws and clips at the wheel-arch liners and on the underside. The corner pieces screw into screw bases that clip into holes molded into the kit. The video doesn't say whether the liner screw points are factory holes, so check your car before you start. That matches our product listing, which describes the kit as needing no cutting or additional bodywork. If a screw point doesn't line up on your car, contact us before you drill anything. Our Returns policy doesn't cover damage caused during installation.

Is the rear wing included?

The kit in the video includes one, but our listing names the front lip, side skirts and rear diffuser. The rear spoiler can be purchased separately in the Optional Parts section. Check the product page for current contents.

What if a part arrives damaged, defective or wrong?

Inspect your order when it arrives. Our Returns policy explains how to report damage or defects, the deadline for reporting, and what isn't covered (for example, damage caused during installation). Delivery times and details are on our Shipping policy page.

Installation steps follow the manufacturer's video and are for reference only. Fitment, hardware and required work can vary by vehicle. For what's covered if a part arrives damaged or defective, see our Returns policy; for delivery details, see our Shipping policy. If you're not comfortable doing the work, have a professional install the kit.

Comments


bottom of page