top of page

Honda Civic Hatchback 11th Gen 2021 Body Kit Install Guide

Nov 9
3 min read

This guide follows the Yofer video for the Honda Civic Hatchback 11th Gen 2021 Body Kit. The kit in the video has front corner pieces, a front splitter, side skirts, and a replacement rear lip with a center light.

White 11th-gen Honda Civic Hatchback with the Yofer side skirts, side view

Watch the full installation

The captions in this video are in Chinese (with Mandarin narration); the written steps below are in English.

What you'll need

  • Front corner pieces, front splitter (assembled from parts), side skirts, rear lip and center light with plug-in harness

  • The supplied screws (the splitter alone uses four to assemble)

  • Adhesion promoter and double-sided tape

  • A cordless driver, screwdrivers and a trim/clip tool

Part 1: Tape prep

Step 1: Tape every piece. Before installing, wipe adhesion promoter onto the tape areas of each piece and apply the double-sided tape.

Wiping adhesion promoter onto a Yofer kit piece for the Civic Hatchback

Part 2: Assemble the splitter

Step 2: Build the splitter. Line up the screw holes and fasten the pieces together with four screws.

Assembling the front splitter with screws

Part 3: Front corner pieces and splitter

Step 3: Remove the factory fasteners. Remove the factory clips and screws under the front bumper.

Removing the factory clips and screws under the front bumper

Step 4: Fit the corners. Peel part of the tape liner in advance and wipe adhesion promoter on the car. Line the corner piece up, fit it and press it down. Refit the clips and screws underneath, and screw both sides.

Lining up the front corner piece on the Civic Hatchback bumper

Step 5: Fit the splitter. Line up the screw posts on both sides and fasten the sides first. Then refit the clips and screw the middle underside.

Lining up the splitter on the screw posts

Part 4: Side skirts

Step 6: Prep. Remove the factory screws and wipe on adhesion promoter.

Removing the factory screws before fitting the side skirt

Step 7: Fit and fasten. Peel the middle section of tape first, line the skirt up, and press it on. Drive screws into the factory screw points, and screw the bottom as well.

Driving a screw into the factory screw point on the side skirt

Part 5: Rear lip and center light

Step 8: Remove the factory rear lip. The new lip replaces the original. Remove the factory clips and screws underneath (there are some inside too), then pry the clips loose.

Removing the factory clips and screws to take off the rear lip

Step 9: Fit the new lip. Mount the center light on the rear lip first. Then fit the lip, press it on, and refit the factory clips and screws.

Two installers fitting the Yofer rear lip on a white Civic Hatchback

Step 10: Wire the light. Bring the light wire out directly below the tail light and connect it to the factory plug through the plug-in harness. Refit the tail light.

Bringing the center-light wire out below the tail light

Tip: the tape and adhesion-promoter routine

In this video, every piece is taped before anything goes on the car. Adhesion promoter goes on both the part's tape areas and the car's bonding surface. Peeling only part of the liner at first, the middle section on the side skirts, lets you line the piece up before the whole strip grabs. Check your promoter and tape instructions for drying time and temperature limits, which the video doesn't state.

FAQ

Do I need to drill holes in my car?

No. The video shows no drilling and no self-tapping screws. The side skirts screw into the factory screw points, with extra screws along the bottom. The front corners, splitter and rear lip use the factory clips and screws plus the splitter's own screw posts. That matches our product listing, which describes the kit as needing no cutting or additional bodywork. If a screw point doesn't line up on your car, contact us before you drill anything. Our Returns policy doesn't cover damage caused during installation.

Does it fit the Civic sedan?

No. The Yofer catalog lists this kit for the 2022-2024 Civic Hatchback (11th Gen). Sedans have their own Civic 11th Gen kits.

How is the center light powered?

In the video it plugs into the factory tail-light connector through the supplied harness. Check your state's rules on rear lighting.

What if a part arrives damaged, defective or wrong?

Inspect your order when it arrives. Our Returns policy explains how to report damage or defects, the deadline for reporting, and what isn't covered (for example, damage caused during installation). Delivery times and details are on our Shipping policy page.

Installation steps follow the manufacturer's video and are for reference only. Fitment, hardware and required work can vary by vehicle. For what's covered if a part arrives damaged or defective, see our Returns policy; for delivery details, see our Shipping policy. If you're not comfortable doing the work, have a professional install the kit.

Comments


bottom of page