top of page

Honda Accord 11th Gen 2023 PRO Body Kit Install Guide

Nov 2
4 min read

This guide follows the installation reference video for the Honda Accord 11th Gen 2023 PRO Body Kit. It covers eight parts in order: assembling and installing the front piece, swapping the grille, assembling and installing the side skirts, assembling and installing the rear piece, and fitting the wing. The video says the kit it shows has 25 pieces.

Silver 11th-gen Honda Accord with the Yofer kit and rear wing installed, rear three-quarter view

Watch the full installation

The captions in this video are in Chinese; the written steps below are in English.

What you'll need

  • The kit parts: front piece with three trim strips, grille with cover panel and trim strips, under-panel, side skirts with segmented trim strips, rear piece with chrome exhaust surrounds and trim strips, and the rear wing

  • The supplied hardware, including the small metal joining plates

  • Adhesion promoter and double-sided tape

  • A cordless driver, screwdrivers and a trim/clip tool

  • A lift or safe support, because the video removes the factory front bumper

Our PRO listing includes the front grille, front lip, rear diffuser and side skirts. The video also shows a rear wing. Check the product page for what your kit includes.

Part 1: Assemble the front piece

Step 1: Fit the trim strips. The front piece is one main body plus three clip-on trim strips. Fit the left and right strips first, then the center strip.

Fitting the clip-on trim strips to the Accord 11th Gen front lip

Step 2: Check the clips. From the back, check that every clip is fully seated.

Part 2: Assemble the grille

Step 3: Build the grille. The grille is a main grille, a cover panel and a pair of trim strips. Clip the strips onto the left and right sides, then check that every clip is secure.

Part 3: Install the front piece

Step 4: Remove the factory bumper. Take off the factory front bumper together with the upper and lower grilles.

Step 5: Fit the under-panel. Clip the supplied under-panel to the front piece.

Clipping the supplied under-panel to the front piece

Step 6: Fit the lower grille. Fit the lower grille to the factory bumper, lining up the clip and screw points.

Fitting the lower grille to the factory Accord front bumper

Step 7: Transfer the side vents. Move the vent pieces from the factory lower grille to where the front piece meets the bumper on each side. Join them with the supplied small metal plates and screws.

Part 4: Swap the grille

Step 8: Remove the factory grille. Release the clips and screws on the back of the factory grille. Unplug the ACC (radar) connector, remove the bracket and take the grille off.

Step 9: Fit the new grille and refit the bumper. Reinstall by reversing the removal steps. Then refit the complete front bumper in its factory position.

Part 5: Assemble the side skirts

Step 10: Fit the trim strips. Each skirt is a main body plus segmented trim strips. Find the front and rear positions of the strips and clip them on.

Accord 11th Gen side skirt main body and segmented trim strips

Step 11: Tape the skirts. Clean the tape areas on the back, wipe on adhesion promoter, and apply double-sided tape.

Applying double-sided tape to the back of the side skirt

Part 6: Install the side skirts

Step 12: Prep the car. Remove the screws at the bottom of the front fender. Clean the rocker panel bonding area and wipe on adhesion promoter.

Step 13: Fit the skirt. Tuck the front of the skirt into the factory wheel-well liner, then slot the rear into its position. Peel the tape liner and press firmly.

Two installers fitting the side skirt to a silver 11th-gen Honda Accord on a lift

Step 14: Fasten it. Secure the front at the factory screw points and the rear with self-tapping screws. Finish with the two screw points underneath.

Securing the rear of the side skirt with a screw near the rear wheel

Part 7: Assemble and install the rear piece

Step 15: Assemble the rear piece. The rear piece is one main body, two chrome exhaust surrounds and three trim strips, all clip-on. Fit the left and right trim pieces first, then the center strip, then the exhaust surrounds. Check every clip from the back.

Clipping the center trim strip onto the rear piece

Step 16: Mount it. Remove the black factory spoiler from the bottom of the rear bumper. Mount the new rear piece in its place and fasten the clips and screws underneath.

Two installers mounting the rear piece on the Accord's rear bumper

Part 8: Install the rear wing

Step 17: Tape the wing. Clean the dedicated tape areas under the wing, wipe on adhesion promoter, and apply double-sided tape.

Wiping adhesion promoter on the rear wing's tape area

Step 18: Position and press. Test-fit the wing with the liner tabs sticking out, and wipe the bonding area on the trunk lid. Line it up, pull the tabs one by one, and press it down.

Tip: the tape and adhesion-promoter routine

The video follows the same order for every taped part: clean, adhesion promoter, tape, test-fit with the liner tabs out, then peel and press. Leaving the liner tabs out lets you position the part before the tape grabs. Check your promoter and tape instructions for drying time and temperature limits, which the video doesn't state.

FAQ

Do I need to drill holes in my car?

No drilling is shown, but the side skirts do add two small screw holes. The front of each skirt uses a factory screw point. The rear end is fixed with a self-tapping screw driven straight through the skirt into the plastic wheel-well liner, with no pilot hole drilled first, so it makes its own small hole in the liner. Everything else (front piece, grille, rear piece) uses clips, the supplied metal plates and factory screw points, and the wing is taped. If a screw point doesn't line up on your car, contact us before you drill anything. Our Returns policy doesn't cover damage caused during installation.

Do I have to remove the front bumper?

Yes, in the video the factory front bumper and grilles come off. The ACC radar connector is unplugged and reconnected. Check that your driver-assist systems work afterward, and have a dealer check radar alignment if you're unsure.

Which Accord years does it fit?

The Yofer catalog lists this kit for the 2023-2026 Honda Accord (11th Gen). Confirm your trim against the product page.

What if a part arrives damaged, defective or wrong?

Inspect your order when it arrives. Our Returns policy explains how to report damage or defects, the deadline for reporting, and what isn't covered (for example, damage caused during installation). Delivery times and details are on our Shipping policy page.

Installation steps follow the manufacturer's video and are for reference only. Fitment, hardware and required work can vary by vehicle. For what's covered if a part arrives damaged or defective, see our Returns policy; for delivery details, see our Shipping policy. If you're not comfortable doing the work, have a professional install the kit.

Comments


bottom of page