top of page

Honda Accord 10th Gen Restyling Front Lip Install Guide

Nov 6
3 min read

The Honda Accord 10th Gen Restyling 2021 Body Kit includes a front lip, made up of two front corner pieces and a center splitter. This guide follows the Yofer factory video, which covers only the front lip. The installer describes it as seven steps. The corner pieces attach with double-sided tape plus the factory clip and screw points, and the splitter bolts to its screw posts.

White 10th-gen Honda Accord with the Yofer front lip installed, front view

Watch the full installation

The captions in this video are in Chinese (with Mandarin narration); the written steps below are in English.

What you'll need

These are the items that appear or are named in the video:

  • Yofer front corner pieces (left and right) and center splitter

  • The supplied double-sided tape and screws

  • Adhesion promoter and a clean wipe

  • A cordless driver or screwdriver

  • A trim/clip removal tool for the factory bumper clips

Yofer front lip corner pieces, center splitter and hardware laid out before installing on a Honda Accord

Part 1: Prepare the corner pieces

Step 1: Wipe on adhesion promoter. Wipe adhesion promoter onto the tape areas of each front corner piece.

Wiping adhesion promoter onto the tape area of an Accord front lip corner piece

Step 2: Apply the double-sided tape. Lay the tape along the mating surfaces one strip at a time. Leave the red liner on for now.

Applying red-liner double-sided tape along the mating edge of the front lip corner piece

Part 2: Prepare the car

Step 3: Remove the factory fasteners. Take out the two factory clips at the bottom and middle of the bumper, and the screws under the fog lights.

Removing factory clips from the underside of the Honda Accord front bumper

Step 4: Clean the bonding area. Clean the areas the corner pieces will stick to, and keep the mounting surface dry and clean.

Part 3: Install the front corner pieces

Step 5: Fit and press. Line up each corner piece, then peel the tape liner off piece by piece. Press firmly along every taped area so the bond holds.

Two installers lining up the front corner piece under the Accord fog light before peeling the tape
Pressing the front corner piece firmly against the bumper to set the tape

Step 6: Refit the fasteners. Reinstall the bottom clips and the middle screws.

Part 4: Install the center splitter

Step 7: Bolt up the splitter. Find where the splitter meets the screw posts and fasten it with two screws on each side. Then fasten the middle at its screw holes.

Driving screws into the screw posts to secure the Accord center front splitter

Tip: the tape and adhesion-promoter routine

In the video, every taped joint gets the same routine. Clean the surface, wipe on adhesion promoter, apply the tape, line the part up, and then peel the liner and press firmly. Work on a clean, dry surface. Check the instructions that come with your adhesion promoter and tape for drying time and temperature limits, because the video doesn't state them.

FAQ

Do I need to drill holes in my car?

No. The video shows no drilling. The two front corner pieces attach with double-sided tape plus the factory clips and the factory screws under the fog lights, which come out and go back in. The center splitter screws into its own screw posts. The cordless tool is only ever used as a screwdriver. That matches our product listing, which describes the kit as needing no cutting or additional bodywork. If a screw point doesn't line up on your car, contact us before you drill anything. Our Returns policy doesn't cover damage caused during installation.

Which Accord years does it fit?

The Yofer catalog lists this kit for the 2021-2022 Honda Accord (the 10th-gen refresh). The Hybrid version covers the same years. Confirm your trim and bumper style against the product page before ordering. A separate Hybrid version of this kit is also listed.

How long does it take?

The video doesn't give a time. Let the tape bond fully before washing or driving hard, and follow the tape maker's guidance.

Is this the whole body kit?

No. This video covers the front lip only. The full kit also includes side skirts, rear aprons and a rear diffuser.

What if a part arrives damaged, defective or wrong?

Inspect your order when it arrives. Our Returns policy explains how to report damage or defects, the deadline for reporting, and what isn't covered (for example, damage caused during installation). Delivery times and details are on our Shipping policy page.

Installation steps follow the manufacturer's video and are for reference only. Fitment, hardware and required work can vary by vehicle. For what's covered if a part arrives damaged or defective, see our Returns policy; for delivery details, see our Shipping policy. If you're not comfortable doing the work, have a professional install the kit.

Comments


bottom of page